材质:不锈钢 | 品牌:德国洛克 | 连接形式:法兰 |
驱动方式:手动、电动、气动 | 介质温度:≤300℃℃℃ | 工作压差:1.0~1.6Mpa |
型号:DE LOCKE | 产品别名:刀型闸阀 | 适用范围:电站、冶金、建筑、锅炉、设备、管道、热能、空调、消防、给排水、水处理、石油化工、造纸印刷厂。 |
流动方向:双向 | 用途:截止 | 适用介质:水 |
压力环境:常压 | 规格:中型 | 产品特性:截止 |
类型(通道位置):二通式 |
进口全封闭式刀闸阀外观精美德国洛克LOCKE维修方便
进口全封闭式刀闸阀产品概述:
德国《DE LOCKE》洛克进口全封闭式刀闸阀是闸板全封闭在阀腔内进行启闭密封的结构,它适合于安装在污水池底下,阀体浸泡在液体里的管道或是地埋式安装阀门的管道环境且压力大于等于PN10的管道.其密封结构是通过闸板关闭下移直到闸板底部斜面与阀体下锲块吻合使得闸板贴紧阀座密封面,从而达到了密封效果.闸板上半圆设有斜度锲块和阀体内腔上斜度锲块吻合并利用PTFE导向圈同闸板平面平稳启闭滑动使密封更加可靠。阀杆上圆型填料处设有双重的Y型和O型密封圈并有倒密封结构,可以***在闸板全开状态下在线进行更换填料,***在长时间状态下阀门的上阀杆密封不漏。
Product overview of imported fully enclosed knife gate valve:
German de lock imported fully enclosed knife gate valve is a structure in which the gate is fully enclosed in the valve cavity for opening and closing sealing. It is suitable for installation under the sewage tank, The sealing structure of the pipeline in which the valve body is immersed in liquid or the pipeline environment in which the buried valve is installed and the pressure is greater than or equal to PN10. The sealing structure is to close and move down through the ram until the slope at the bottom of the ram coincides with the wedge block of the valve body, so that the ram is close to the sealing surface of the valve seat, The upper semicircle of the ram is provided with a slope wedge block and a slope wedge block on the inner cavity of the valve body, and the PTFE guide ring is used to open and close smoothly with the plane of the ram to make the sealing more reliable. Double Y-shaped and O-shaped sealing rings and inverted sealing structure are set at the circular packing on the valve stem, which can ensure that the packing can be replaced online when the ram is fully open and that the upper valve stem seal of the valve will not leak for a long time.
进口全封闭式刀闸阀产品性能:
1、公称压力:PN1.0~1.6Mpa
2、通径范围:DN50~DN1400
3、连接形式:对夹;法兰
4、传动机构:手轮,涡轮,气动,电装,液动,电液动,链轮盘
5、主要材质:WCB,CF8,CF8M
6、闸板材质:F55, F53,2205, SS310, SS316L,SS316, SS304
7、密封材质:EPDM,NBR,PTFE
8、填料密封:芳纶,高水机,四氟,橡胶,石墨
9、适用介质:适用于泥浆、城市污水处理、糖厂、造纸、医药、化工等油品,等固体介质。
进口全封闭式刀闸阀产品特点:
1、斜度面楔块;
2、四氟圈;
3、阀杆倒关密封;
4、平面支撑点;
5、侧面支撑点。
进口全封闭式刀闸阀产品业绩:
1、上海纺织(集团)有限公司
2、徐州盛泉洗煤厂
3、浙江华都纺织集团有限公司
4、恒安集团
5、金东纸业有限公司
6、山东晨鸣纸业集团股份有限公司
7、潍坊砂矿有限公司
8、华东有色尾矿公司
9、福建建阳祥康织造有限公司
10、介休市晋强洗煤设备制造有限公司
11、微山县汇永煤炭洗选有限公司
12、山西临汾如意洗煤有限公司
13、西湖洗煤厂
14、山东洗煤厂
进口全封闭式刀闸阀产品安装:
1、安装前须检查阀门腔内和密封面等部位,不允许有污物或砂粒附着;
2、各连接部位螺栓,要求均匀拧紧;
3、检查填料部位要求压紧,既***填料的密封性,也要***闸板开启灵活;
4、用户在安装阀门前,必须校对阀门型号,连接尺寸及注意介质流向,***与阀门要求一致性;
5、用户在安装阀门时,必须预留阀门驱动的必要空间;
6、驱动装置的接线须按线路图进行;
7、气动对夹刀闸阀必须定期保养,不得随意碰撞及挤压,以免影响密封。